Service quick specs OEM factory data
Capacities, torques and tune-up values from the factory service manual.
This engine holds 7.6 qt of 5W-20 API engine oil, USE CASTROL SAF-X0 OR EQUIVALENT in the differential. Torque lug nuts to 95 ft-lbs, the oil drain plug to 18.0-22.0 ft-lbs. Note the cylinder-head bolts finish on a torque angle (torque-to-yield) — they stretch permanently and should be replaced, not reused, during any head service.
Lubricants & capacities
| Automatic Transmission Fluid | Shell M1375.4 |
| Automatic Transmission Fluid Capacity | 9.0-11.0 |
| Differential Gear Oil | USE CASTROL BOT 720 OR EQUIVALENT |
| Differential Gear Oil Capacity | 2.7 Pints |
| Differential Gear Oil | USE CASTROL SAF-X0 OR EQUIVALENT |
| Differential Gear Oil Capacity | 1.7 qt |
| Engine Oil | 5W-20 · API |
| Engine Oil Capacity | 7.6 qt |
Engine torques
| Engine Oil Pan Drain Plug | 18.0-22.0 ft-lbs |
Battery & A/C
| Refrigerant | R134a |
| Refrigerant Capacity | 1.65 lbs |
| Oil Group | PAG |
| Oil Type | 46 |
| Standard BCI Group Number | 49 |
| Standard BCI Cranking Performance | 800 cca |
Service checks
| Regulated Fuel System Pressure (Without Vacuum) | 65.0 Low pressure side. psi |
| Regulated Fuel System Pressure (With Vacuum) | 65.0 Low pressure side. psi |
Brakes
| Brake Application | HIGH PERFORMANCE BRAKES / STANDARD BRAKES |
| Torque Caliper to Bracket | 21 ft-lbs |
| Torque to Knuckle | 76 ft-lbs |
| Minimum Pad Thickness | 0.080 in |
| Brake Application | HIGH PERFORMANCE BRAKES / STANDARD BRAKES |
| Rotor Runout Limit | 0.004 in |
| Rotor Nominal Thickness From | 1.02 in / 0.79 in |
| Rotor Nominal Thickness To | 1.02 in / 0.79 in |
Multi-step torque procedures OEM · verified
Crankshaft Pulley and/or Damper Bolts — tightening sequence 1 stages
| 1 | 148 ft. lbs., step 2: 180 | 148 ft. lbs |
Cylinder Head — tightening sequence 6 stages
Prep Do not reuse old bolts. Coat new bolts with engine oil. Tighten all bolts to finger tight then continue on with the following procedure.
| 1 | Bolts 1-10 | 15 ft. lbs |
| 2 | Bolts 10 | 25.8 ft. lbs |
| 3 | Bolts 1-10 | 360 degrees |
| 4 | Bolts 1-10 | 120 degrees |
| 5 | Larger top recessed bolts | 18.5 ft. lbs |
| 6 | Two bolts below larger recessed bolts | 8.8 ft. lbs |
Factory maintenance schedule OEM · verified
Normal service, condensed from the factory interval matrix.
Under the factory schedule, replace the engine oil and filter every 16,000 mi; spark plugs every 96,000 mi; coolant every 16,000 mi. The big-interval services (every 16,000 mi for coolant, and the transmission fluid) are the ones owners most often skip — on a lower-mileage example, assume the original fluids are still in it and check them first.
| Every 16,000 mi | Brake Hydraulic System (inspect fluid level) · Brake Linings (inspect) · Brake Rotor (inspect) · Engine Assembly (leak inspection) · Engine Coolant System (inspect fluid level) · Engine Oil (drain & refill) |
| Every 32,000 mi | Battery (inspect electrolyte level) · Cabin Air Filter (replace) · Temperature Controlled Seat Air Filter (replace) |
| Every 48,000 mi | Engine Air Filter Element (replace) |
| Every 96,000 mi | Spark Plugs (replace) |
| At 144,000 mi | Drive Belt (replace) |
Recalls NHTSA · verified
Showing 2 of 7 campaigns on record for this vehicle.
16V796000Fuel System, Gasoline:Delivery:Hoses, Lines/Piping, And FittingsReported 01/11/2016
Jaguar Land Rover North America, LLC (Jaguar) is recalling certain model year 2013-2015 Jaguar XF vehicles manufactured May 22, 2013, to June 15, 2015 and equipped with 2.0L GTDi engines. The affected vehicles may have… Remedy: Jaguar will notify owners, and dealers will inspect the fuel line for abrasions, replacing it as necessary and install additional clips, free of charge. Parts are not yet…
16V137000Steering:Hydraulic Power Assist SystemReported 07/03/2016
Jaguar Land Rover North America, LLC (Jaguar) is recalling certain model year 2013-2015 Jaguar XF vehicles manufactured May 16, 2012, to June 15, 2015 and equipped with 2.0L GTDi engines. The retaining bolt for the… Remedy: Jaguar will notify owners, and dealers will replace the FEAD pulley assembly, free of charge. Owners were sent interim notifications on May 28, 2016. This recall began July 1…