Mini›Cooper Clubman›2016›Overview/mini/cooper-clubman/2016/base/

2016 Mini Cooper Clubman

Factory specifications, fluid capacities, torque values, EPA fuel economy and the federal safety record for the 2016 Cooper Clubman.

Transmission Automatic (S6)

The 2016 Mini Cooper Clubman is EPA-rated at 25/33/28 mpg city/highway/combined.

Quick specs

Fluid capacities, tune-up values and fuel economy at a glance.

EPA fuel economy25/33/28 mpgEPA · verified

Fitment & sizes

Replacement part sizes and factory part numbers — battery, bulbs, filters and belts.

From the factory this vehicle uses a BCI NS · NS CCA battery, OE oil filter 11427622446. Each part links to every other vehicle that shares it, so a part you already stock may fit more of your fleet than you'd expect.

Battery groupBCI NS · NS CCAOEM · verified

Tire size175/65R15OEM · verified

Wheel / rim5.5 inOEM · verified

OE service part numbers OEM · verified

Engine oil filter	11427622446
Engine air filter	13717568728 alt 13717561235
Spark plug	12122293697 alt 12122158165
Battery	61217575326 alt 61217571896
Front wiper blades	61615A87CC6
Thermostat	11518613803 alt 11518613804
Cabin air filter	64319127516

Full specifications

Engine, drivetrain, dimensions and economy.

Engine & drivetrain NHTSA vPIC

Transmission

Automatic (S6)

Dimensions & weight NHTSA vPIC

Overall length	151.2 in
Overall width	68.1 in
Overall height	55.5 in
Wheelbase	98.4 in
Curb weight	2606 lb
Track (front / rear)	59.1 / 59.1 in
Weight distribution (front / rear)	61/39

Ratings & economy EPA / vPIC

EPA city / highway / combined	25 / 33 / 28 mpg
Drivetrain	Front-Wheel Drive
Recommended fuel	Premium Gasoline

Service quick specs OEM factory data

Capacities, torques and tune-up values from the factory service manual.

This engine DOT 4 brake fluid. Torque the oil drain plug to 18.0 ft-lbs. The firing order is 1-3-2. Note the cylinder-head bolts finish on a torque angle (torque-to-yield) — they stretch permanently and should be replaced, not reused, during any head service.

Lubricants & capacities

Automatic Transmission Fluid	ATF
Automatic Transmission Fluid Capacity	6.3
Brake Fluid	DOT 4
Clutch Fluid	DOT 4
Power Steering Fluid	Pentosin CHF11S

Engine torques

Camshaft Bearing/Carrier Cap Bolts or Studs	9 ft-lbs
Exhaust Manifold to Cylinder Head Bolts	18.4
Intake Manifold to Engine Bolts	7.3
Engine Oil Pan Drain Plug	18.0-22.0 ft-lbs
Engine Oil Pan Drain Plug	23.0 ft-lbs
Engine Oil Pan Drain Plug	18.0 ft-lbs

Chassis torques

Front Wheel Hub	Use new nut and tighten to 134.0 ft-lbs
Rear Wheel Hub	Use new nut and tighten to 134.0 ft-lbs

Ignition

Cylinder Firing Order	1-3-4-2
Cylinder Firing Order	1-3-2
Spark Plug Manufacturer	BMW
Spark Plug Gap	Not adjustable in
Spark Plug Torque	14.8-19.2 ft-lbs

Battery & A/C

Refrigerant	R134a
Refrigerant Capacity	1.05-1.10 lbs
Standard BCI Group Number	140R
Standard BCI Cranking Performance	480 cca

Service checks

Pressure Test	22 psi
Radiator Cap Pressure Relief	18-22 psi

Brakes

Brake Caliper Bolt to Carrier Torque	Front: 26; Rear: 103 /; Front: 26; Rear: 22-
Brake Caliper Carrier to Hub Bolt Torque	Front: 81; Rear: 74 Use; Front: 84; Rear: 74
Minimum Pad Thickness	Front: 0.145; Rear: 0.145 pads
Vented Rotor Minimum Thickness for Replacement	Stamped on rotor
Vented Rotor Minimum Thickness after Refinish	Stamped on rotor

Multi-step torque procedures OEM · verified

Connecting Rod (Large End) Bearings — tightening sequence 1 stages

4 ft. lbs., Step 2: 11 ft. lbs., Step 3: 130

4 ft. lbs

Cylinder Head — tightening sequence 1 stages

22.0 ft. lbs. Step 2: 90 degrees Step 3: 180

22 ft. lbs

Cylinder Head — tightening sequence 7 stages

Prep Do not reuse old bolts. Coat new bolts lightly with specified motor oil.

1	M10 Bolts	22 ft. lbs
2	M10 Bolts	90 degrees
3	M10 Bolts	90 degrees
4	M8X95 Bolts	11 ft. lbs
5	M8X95 Bolts	90 degrees
6	M8X95 Bolts	90 degrees
7	M8X35 Bolts	22 ft. lbs

Cylinder Head — tightening sequence 3 stages

Prep Do not reuse old bolts. Coat new bolts lightly with specified motor oil.

1	22.0 ft. lbs.	22 ft. lbs
2	66.0 ft. lbs.	66 ft. lbs
3	180 degrees	180 degrees

Engine Flywheel Bolts — tightening sequence 1 stages

6 ft. lbs., Step 2: 22 ft. lbs., Step 3: 90

6 ft. lbs

Main Bearings — tightening sequence 1 stages

37 ft. lbs., Step 2: 150

37 ft. lbs

Factory maintenance schedule OEM · verified

This vehicle uses condition-based service — it signals maintenance needs through its onboard service indicator rather than fixed mileage intervals. Items on the factory schedule:

Replace	Cabin Air Filter · Engine Oil Filter · Engine Air Filter Element · Engine Oil · Spark Plugs
Inspect	Underbody · Windshield Washer System · Air Bag System · Parking Brake System · Tire & Wheel Assembly · Steering System · Brake Rotor · Brake Line
Road test	Universal Vehicle Operation
Inspect Fluid Level	Engine Coolant System
Reset	Tire Pressure Monitoring System
Drain, Refill & Bleed	Brake Hydraulic System