Factory specifications, fluid capacities, torque values, EPA fuel economy and the federal safety record for the 2008 JOHN COOPER WORKS - Hatchback R56.
The 2008 Mini JOHN COOPER WORKS - Hatchback R56 takes 4.4 qt of 5W-30 engine oil.
Fluid capacities, tune-up values and fuel economy at a glance.
Replacement part sizes and factory part numbers — battery, bulbs, filters and belts.
From the factory this vehicle uses a BCI 47 · 480 CCA battery, OE oil filter 11427562249. Each part links to every other vehicle that shares it, so a part you already stock may fit more of your fleet than you'd expect.
| Engine oil filter | 11427562249 alt 11427509211 |
| Engine air filter | 13717568728 alt 13717561235 |
| Fuel filter | 11252754870 alt 16146757196 |
| Battery | 61217575326 alt 61217571896 |
| Front wiper blades | 61610028137 |
| Thermostat | 11537596787 alt 11518613803 |
| Cabin air filter | 64319127516 alt 64319257505 |
Capacities, torques and tune-up values from the factory service manual.
This engine holds 4.4 qt of 5W-30 engine oil, DOT 4 brake fluid. Torque lug nuts to 103 ft-lbs.
| Automatic Transmission Fluid | With CVT: BMW part number 83220136376 |
| Brake Fluid | DOT 4 |
| Engine Coolant | ETHYLENE GLYCOL |
| Engine Oil | SYNTHETIC · 5W-30 |
| Engine Oil Capacity | 4.4 qt |
| Engine Oil | SYNTHETIC · 5W-30 |
| Engine Oil Capacity | 4.8 qt |
| Engine Oil | SYNTHETIC · 5W-30 |
| Camshaft Bearing/Carrier Cap Bolts or Studs | 22 ft-lbs |
| Camshaft Bearing/Carrier Cap Bolts or Studs | 6 ft-lbs |
| Intake Manifold to Engine Bolts | 19 ft-lbs |
| Exhaust Manifold to Cylinder Head Bolts | 18 ft-lbs |
| Intake Manifold to Engine Bolts | Bolts: 11, nuts: 15 ft-lbs |
| Exhaust Manifold to Cylinder Head Bolts | 18.4 ft-lbs |
| Intake Manifold to Engine Bolts | Bolts: 11, nuts: 15 ft-lbs |
| Exhaust Manifold to Cylinder Head Bolts | 18.4 ft-lbs |
| Lug Nuts | 103 ft-lbs |
| Curb Idle Speed (No Load) | 770 rpm |
| Curb Idle Speed Variance (No Load) | 50 rpm |
| Spark Plug Manufacturer | BMW |
| Spark Plug Gap | Not adjustable in |
| Spark Plug Torque | 14.8-19.2 ft-lbs |
| Refrigerant | R134a |
| Standard BCI Group Number | 47 |
| Standard BCI Cranking Performance | 480 cca |
| Pressure Test | 29.0 psi |
| Radiator Cap Pressure Relief | 18-22 psi |
| Thermostat Opening Temperature | ------- °F |
| Engine Compression | 116-174 PSI. 43 maximum variation. psi |
| Torque to Knuckle | 81 ft-lbs |
| Minimum Pad Thickness | Front: 0.118; Rear: 0.0118 in |
| Rotor Nominal Thickness From | 0.394 in / 0.866 in / 0.945 in |
| Rotor Nominal Thickness To | 0.394 in / 0.866 in / 0.945 in |
| Rotor Minimum Machining | 0.031 in |
| Rotor Discard at or Under | 0.331 in / 0.803 in / 0.882 in |
| Rotor Finish | 0.00013 μin |
| 1 | 4 ft. lbs., Step 2: 7 ft. lbs., Step 3: 130 | 4 ft. lbs |
| 1 | 4 ft. lbs., Step 2: 11 ft. lbs., Step 3: 130 | 4 ft. lbs |
| 1 | 6 ft. lbs., Step 2: 22 ft. lbs., Step 3: 90 | 6 ft. lbs |
| 1 | 6 ft. lbs., Step 2: 22 ft. lbs., Step 3: 90 | 6 ft. lbs |
| 1 | 22 ft. lbs., Step 2: 150 | 22 ft. lbs |
| 1 | 37 ft. lbs., Step 2: 100 | 37 ft. lbs |
Normal service, condensed from the factory interval matrix.
Under the factory schedule, replace the spark plugs every 100,000 mi.
| Every 100,000 mi | Oxygen Sensor (replace) · Spark Plugs (replace) · Transmission Assembly (drain & refill) |
The most common OBD-II codes for this vehicle's emissions system. These are standardized SAE J2012 definitions, not vehicle-specific fault reports.
Decode factory build data for a specific vehicle by VIN.
Find every vehicle that shares this one's battery, bulbs, oil capacity, platform or parts.
Cross-vehicle references for the kinds of data on this page.
4.4 qt of USE MINI SYNTHETIC 5W-30 MOTOR OIL, per the factory manual.