Factory specifications, fluid capacities, torque values, EPA fuel economy and the federal safety record for the 2017 Micra.
Engine, drivetrain, dimensions and economy.
| Overall length | 150.8 in |
| Overall width | 65.7 in |
| Overall height | 60.2 in |
| Wheelbase | 96.5 in |
| Curb weight | 2302 lb |
| Track (front / rear) | 57.5 / 57.9 in |
| Weight distribution (front / rear) | 59/41 |
Capacities, torques and tune-up values from the factory service manual.
Torque the oil drain plug to 25.0 ft-lbs. The firing order is 1-3-4-2. Note the cylinder-head bolts finish on a torque angle (torque-to-yield) — they stretch permanently and should be replaced, not reused, during any head service.
| Crankshaft Position (CKP) Sensor Bolt(s) | 5.1 ft-lbs |
| Camshaft Position (CMP) Sensor Bolt(s) | 5.1 ft-lbs |
| Camshaft Sprocket and/or Gear Bolt(s) | 58.0 ft-lbs |
| Engine Coolant Temperature (ECT) Sensor Bolt(s) | 18.0 ft-lbs |
| Engine Flywheel Bolts | 80 ft-lbs |
| Engine Flywheel Bolts | 80.0 ft-lbs |
| Intake Manifold to Engine Bolts | 20 |
| Engine Oil Pan Drain Plug | 25.0 ft-lbs |
| Cylinder Firing Order | 1-3-4-2 |
| Spark Plug Manufacturer | Nissan |
| Spark Plug Gap | 0.043 in |
| Spark Plug Torque | 14.0 ft-lbs |
| RPM | @IDLE rpm |
| 1 | 14 ft. lbs., Step 2: 60 | 14 ft. lbs |
| 1 | 20.0 ft. lbs. | 20 ft. lbs |
| 2 | Back off 360.0 degrees | 360 degrees |
| 3 | 14.0 ft. lbs. | 14 ft. lbs |
| 4 | 60.0 | |
| 1 | 22.0 ft. lbs. | 22 ft. lbs |
| 2 | + 60 | |
| 1 | 26.0 ft. lbs. | 26 ft. lbs |
| 2 | + 60 | |
Prep Measure the diameter of each cylinder head bolt at point A and point B. Point A = 10.00 mm from thread end and point B = 40.00 mm from thread end. If either diameter is less than 0.15 mm Do not reuse old bolts. Use new bolts coated with clean engine oil. Tighten all bolts to finger tight then continue on with the following procedure.
| 1 | 30.0 ft. lbs. | 30 ft. lbs |
| 2 | 60 degrees | 60 degrees |
| 3 | Loosen bolts 360 degrees in reverse order | 360 degrees |
| 4 | 30 ft. lbs. | 30 ft. lbs |
| 5 | 75 degrees | 75 degrees |
| 6 | 75 degrees- | 75 degrees |
| 1 | 24 ft. lbs., Step 2: 60 | 24 ft. lbs |
| 1 | 24.0 ft. lbs. | 24 ft. lbs |
| 2 | 60.0 | |
The most common OBD-II codes for this vehicle's emissions system. These are standardized SAE J2012 definitions, not vehicle-specific fault reports.
Decode factory build data for a specific vehicle by VIN.
Cross-vehicle references for the kinds of data on this page.